Skip to Content

How to Make a Rose Gold Epoxy Resin Coaster

How to Make a Rose Gold Epoxy Resin Coaster

Sharing is caring!

Make sure to read through the instructions of the product you are using before starting a project.

Whenever working with resin it is important to be in a well-ventilated area that is between 70-80 degrees with little to no humidity.

Use Personal Protection Equipment (PPE) mainly, gloves. Though, depending on the size of your project and the products you are using, safety glasses and a respirator are also a good idea.

Always work with resin in a well-ventilated area. When working with small amounts of low VOC types of resin for a short amount of time you potentially could get away without a respirator. But for this particular project it is definitely needed.

To check the fit and seal of the respirator on your face you’ll want to put your hand over the output in the center of the mask and exhale forcefully. If any air escapes around the edges of the mask you may need to make adjustments or purchase another size. I’ve included the link for the Medium size of the respirator that I use because it fits the majority of people. I, personally, wear a small because it fits my petite face best.

The cartridges are the most important part! They are effective for approximately 24 hours. That may not seem like long, but if they are stored in an airtight container than they last much longer. I don’t take mine out until right before I am going to open the resin. You should not be able to smell anything outside of the mask. If you can smell the resin through your mask, than the cartridges have gone bad and need to be replaced.

Safety goggles or glasses should also be worn to prevent any chemicals from getting in your eyes in the case of a spill or splash.

Make sure your silicone mold is free of debris and moisture before casting.

For this particular project each coaster takes about 4 oz of resin.

A lot of epoxy resins will come in two parts, and depending on the one you use, the ratios may be different. For MakerPoxy it is a simple 1:1 ratio, which means if you want 4 oz to work with, you should pour 2 oz of each part. You’ll always want to pour the resin before the hardener (or activator etc) with this particular resin the bottles are marked with “A” and “B”.

Using a stirring cup is really handy because it will have the liquid measurements printed on it which makes measuring way easier!

Everything Resin Newsletter

Resin tips, tricks and more straight to your inbox.

    We respect your privacy. Unsubscribe at any time.

    If you are planning on making several items, you may want to pour the resin in smaller batches, rather than all at once, if you’re using a time-consuming technique.

    With a popsicle stick, stir at a slow-medium pace until the two parts are thoroughly mixed together, about a full minute. Make sure to circle around to scrape the sides and then push the stick down into the middle and pull some of the bottom up. This is crucial! If it is not stirred enough you may end up with areas that don’t cure! If you stir too fast then lots of air is whipped up into the resin, causing it to become full of bubbles.

    Once the stirring is finished, the next 30 minutes are going to be the workable time. I wasn’t too worried since I wasn’t doing anything too crazy (for once).

    Pour the resin into the mold, make sure the ridges are filled up and there is a layer on the main surface. Do not fill it to the top yet, you’ll need some room for the pretty stuff.

    Pass a heat gun, lighter or torch over the resin in the mold to help pop some of the bubbles. I like to do this before I start adding the inclusions.

    Join Today

    All of my tips and tricks straight to your inbox.

      Powered By ConvertKit

      An important thing to keep in mind when casting resin in this shape of mold, is that what you are looking at is the bottom. So you have to think backwards, putting the top pieces in face down and working up to the back.

      I like to put my biggest pieces of rose petals and gold foil flakes down first and then add in the smaller pieces as I go. Using tweezers is a great way to put your pieces down and then use a toothpick to submerge them into the resin.

      I tried to distribute the petals and gold evenly throughout the coaster, working on creating a greater sense of depth by pushing some things down into the resin further than others.

      Once I had the design how I liked it, I gently added more resin to the top with a popsicle stick to keep things from moving around too much. Filling it all the way to the top.

      Then it’s a waiting game…put something over your project to protect from any debris while it cures. After 24 hours it should be ready to take out of the mold!

      First work your way around it by pulling the edges away to make sure nothing is stuck. Then pull the silicone mold away from the resin coaster you just cast!

      From here you can sand the bottom if it has rough edges with wet 220 and up sandpaper. Then touch it up with a little clear nail polish.

      You may also like…

      Wood and Blue Resin Charcuterie board cheese platter
      Wood and Blue Resin Charcuterie board cheese platter

      This site uses Akismet to reduce spam. Learn how your comment data is processed.

      Koi Pond Resin Art Coaster Ideas - Olivia OHern

      Saturday 9th of October 2021

      […] How to Make a Rose Gold Epoxy Resin Coaster Easy Unicorn Glitter Epoxy Resin Coaster How To […]

      How to Make a Live Edge Epoxy Table | Olivia OHern

      Friday 11th of June 2021

      […] How to Make a Rose Gold Epoxy Resin Coaster Easy Unicorn Glitter Epoxy Resin Coaster How To […]

      How to Make an Easy Modern Epoxy Resin Tray | Olivia OHern

      Monday 7th of June 2021

      […] Rose Petal & Gold Foil Epoxy Resin Coasters […]

      Easy Unicorn Glitter Epoxy Resin Coaster How To | Olivia OHern

      Thursday 20th of August 2020

      […] to focus on adding colors! What better way than with this unicorn glitter coaster? Go back to my Rose Gold Coaster post for all of the important starting […]

      This site uses Akismet to reduce spam. Learn how your comment data is processed.